CRT Monitör Standart Onarım Bedelleri

15” CRT Monitör Onarım Ücreti                 

17” CRT Monitör Onarım Ücreti                                  

(Tüp, Trafo ve işlemci  hariç onarım fiyatlarıdır )

LCD Monitör Standart Onarım Bedelleri

15” LCD Monitör Onarım Ücreti              

17” LCD Monitör Onarım Ücreti              

19” LCD Monitör Onarım Ücreti             

(Panel, invertör kartı, video kartı, adaptör, florasan ve işlemci değişimi hariç onarım fiyatlarıdır.)

ÖZEL ELEKTRONİK VE BÜRO MAKİNELERİ

Karabaş Mah.Müneccim Arif Sok.Eda Aprt.No:22/a İzmit

Sipariş için : 0262 324 07 72

Online MSN : ozel-elektronik.com@hotmail.com  destek@ozel-elektronik.com

*** Türkiye’nin her yerinden dolum yapılamaktadır. Kargo fiyatları için lütfen arayınız. Uygun kargo fiyatları ile hizmetinizdeyiz.

Muadil lamba, ait olduğu markadan farklı olarak bir başka marka projeksiyonda kullanılan orijinal lambadır.

Sizlere uygun fiyatlarda çözüm ulaştırma amacıyla yıllardır çalışıyoruz. Projeksiyon lambalarının karakteristik yapılarını inceleyip test edip birbirine alternatif uyabilecek lamba modellerinin tespitlerini yaptık.

Okullara Özel Tamir Fiyatları

Orijinal lamba fiyatı yüksek olan ya da temini olmayan ürünlerde
lamba haznesini tamamen değiştirip daha ekonomik fiyatlarla sizlere muadil lamba çözümleri sunmaktayız.

Online Sipariş Msn: kartus@metaj.com.tr

Skype : metaj.bilgisayar

 Tel:  0 262 332 34 33

 
Platforms
- Dos-Windows version
Well, … it works!

- Linux && BSD version
Users can work on cmos backup but they need root priviledge to
use ioperm function to have full access to cmos.

- Windows NT, 2000, XP, 2003
To work on cmos memory, ioperm need to be installed and running.
ioperm gives direct port I/O access for specified ports to user-mode process
(ring 3) using Ke386SetIoAccessMap and Ke386IoSetAccessProcess kernel functions.

1- You need administrator priviledges to install this driver
“ioperm.exe -i”
2- Start the service if needed with “net start ioperm”
3- Run “Cmospwd_win.exe”

WARNING: You should disable or uninstall ioperm
with “ioperm.exe -u” if you don’t want to decrease
your security!

—————————————————
—————————————————
¦  Typical Usage for DOS and all Windows users    ¦
—————————————————
—————————————————

1)  Identify your BIOS manufacturer (usually displayed at boot-up)

2)  Start in DOS, or start a DOS session in Windows 95/98/ME.
    For Windows NT or Windows 2000 boot from a DOS or Windows 95/98 boot
    disk  (you can find boot disks at www.AnswersThatWork.com), and run
    CMOSPWD from your boot floppy (or another floppy).

3)  C:              [Enter]
    cd \CMOSPWD    [Enter]
   
4)  Type  CMOSPWD  at the DOS prompt and press Enter.

5)  CMOSPWD will display a list of possibilities.  Use the possibilities
    itemised against your BIOS manufacturer.
    Remember :
   
         a)  For AWARD BIOSes, use the Numeric Keypad (with NumLock ON).
         b)  AWARD 4.50PG BIOS always accepts  “AWARD_SW”, or “d8on”,
             or “589589″.
         c)  Old Phoenix BIOSes will accept  “phoenix”.
      
6)   If the standard method does not work, then try to kill
     the CMOS password with  CMOSPWD /K  (and press Enter),
     and then see if you can get into the CMOS without a password.
     If you can, you successfully “killed” the old CMOS password.
     DO NOT KILL THE CMOS ON LAPTOPS!

—————————————————
—————————————————
|General Usage  (List of commands)                |
—————————————————
—————————————————

cmospwd [/d]
cmospwd [/d] /[wlr] cmos_backup_file  write/load/restore
cmospwd /k                            kill cmos
cmospwd /m[01]*                       execute selected module
 
 /d to dump cmos in ascii and scan code
 /m0010011 to execute module 3,6 and 7

Keyboard:
 /kfr French AZERTY
 /kde German QWERTY
 default is US QWERTY

—————————————————
—————————————————
|Laptops                                          |
—————————————————
—————————————————
On laptops, the password is usually stored in an eeprom on the motherboard,
you need an eeprom programmer (electronic device) to retrieve it.

Acer 630: eeprom 93c56 ?
Compaq M700: eeprom 24C02
Dell Inspirion 5100: eeprom 93lc46, password in scan code at 0×310
Dell Inspirion 7500: eeprom 24c164
Dell Inspirion 8100: eeprom 24c02
Dell Latitude C600: eeprom 24c02, password in scan code at 0×00, 0×10 and 0×90
Dell Latitude C610: eeprom 24c02, password in scan code at 0×00, 0×10, 0×80 and 0×90
Dell Latitude CPI: eeprom 24c02, password in scan code at 0×00, 0×10, 0×80
Dell D600: eeprom 24c04, password in scan code at 0×110
IBM Thinkpad X20: eeprom 24RFC08CN, password in scan code at 0×338
IBM TP 240: eeprom ?, password in scan code at 0×338.
IBM TP 380Z: eeprom 24c01, password in scan code at 0×38 and 0×40
IBM TP 390: eeprom 24c03 (be carrefull, there are two eeprom)
IBM TP 560X: eeprom 24c01, password in scan code at 0×38 and 0×40
IBM TP 570: eeprom ?, password in scan code at 0×338 and 0x3B8.
IBM TP 750C,755CX,760C,765D: eeprom 93c46, password in scan code at 0×38 and 0×40
            OKI M811b may be written on the chip. Search near pcmcia slot or
     adjacent the floppy connector on the top side of the board
IBM TP 770:  eeprom 24c01
IBM TP 600E, T21, T23: 14 PIN 24RF08
IBM TP T20,X20,X30: 24RF08, password in scan code at 0×338 and 0×340
HP Omnibook 900,2100,4150,7150: eeprom AT24c164, 0x6D-0x7F area, unknow algo
              put a 00 at 0x7F to clear admin password
HP Omnibook 6000: eeprom 24c08 or 24c164 0×50-0xBF area
    (maybe 0×50-0x6F only), unknow algo
HP Omnibook 6100: eeprom 24c08
HP Omnibook XE3: eeprom 24c16
HP Omnibook 770x: eeprom 24c01
HP Pavilion ze4455ea: eeprom 24c08
HP VECTRA VL18: http://h200001.www2.hp.com/bc/docs/support/SupportManual/lpv06673/lpv06673.pdf
Sony pcg-fx950: eeprom 93c46 ?
Toshiba 74600C: eeprom 93c56
VAIO 641: eeprom 24c02 write zero at 0×0
be carrefull, there are two eeprom you must unsolder one to the pci
controler it is in the down side of the bord

VAIO 8851
eeprom 24c02 (ic 903) write zero at adres 0×0
the down side of the board

VAIO srx 87: eeprom 2408 write zero at 0×0
the ic is behind the modem in the top side of the board

VAIO PCG-FX150, eeprom 24c04 near the reference IC1103
VAIO PCG-GRX560, eeprom 24c04 near the reference IC1001

You can get/buy eeprom programmer in electronic shops or labs, you need
another PC to use it.
You can desolder the eeprom with hot air or you can try to “clip” the
eeprom. With the eeprom programmer, backup your eeprom and run
“cmospwd /d /l eeprom_backup”. If you don’t see the password, you can try
to fill the eeprom with zero or FF, don’t forget the reset the cmos.

—————————————————
—————————————————
|Toshiba                                          |
—————————————————
—————————————————
Differents passwords give the same 32-bit CRC, so CmosPwd can only give one
of them.
To reset the password of an old Toshiba, you can use KeyDisk. (cf my web page)
If this doesn’t work, you can try to build the Toshiba Parallell loopback.
To make a simple device that you connect to your parallell port, a lot of
Toshiba computers remove the password when you boot it up.
The device, named “loopback” by some, could be made out of any
parallell wire with 25pins connectors (db25). You should connect
these pins: 1-5-10, 2-11, 3-17, 4-12, 6-16, 7-13, 8-14, 9-15, 18-25.

A db25 looks like:
1    13
_______
\_____/
14   25

—————————————————

Divers
- Medion
Try the password “am8888egh”.
- Award 4.50PG
There is an universal password AWARD_SW.
(d8on, 589589 … works too)
- Award 4.5x using DFI motherboards
The universal password is “Y. C. Lu” (spaces and capitals as shown).
Information from David Walker.
- Award
Differents passwords give the same 32-bit CRC, so CmosPwd can only give one
of them. Use the numeric keypad.
- COMPAQ LTE 5300 notebook
Tolga Sinan Guney: there is a reset jumper on the motherboard
- DIGITAL PC300, Phoenix 4.0 Rel 6.0,0
Rene Pocisk: cmospwd /k works
- Fujitsu ICL
aksion: passwords are stored in EEPROM
- Fujitsu Point 1600
William Simcox: “I was able to clear the password and reset BIOS to
default values using CMOSPWD /K”
- Phoenix
There is a backdoor in old version of Phoenix BIOS, the universal
password is “phoenix”.
- Siemens Nixdorf
PCD-4ND, Michael: You can clear the password of this phoenix 1.03 with “cmospwd /k”
Scenic Mobil 700, Josef Benda: “cmospwd /k” works! Phoenix Note BIOS v4.0
Scenic Mobile 510AGP, Bernd: “cmospwd /k” works! Phoenix 4.0 R6 Version 3F31 dated 9.2.2000
- Acer Travelmate 530
“cmospwd /k” removes the password.
- Acer travelmate 2450
“cmospwd /k” removes the password.
- Sony Vaio PCG505HS
Brad Frisbie: “cmospwd /k” works, Phoenix 6 R4
- Sony Vaio PCG-FR105
Andrea Michele Zoia: ‘cmospwd_win /k’ removes the password.
- IBM NetVista 8303-41G
Roel:  CmosPwd /k works, Phoenix Bios 4.0 Release 6.0.
- Panasonic CF-25
Stefan Stevens: CmosPwd /k works
- Tulip Vision Line bn 100
CmosPwd /k works, PhoenixBios 4.0 Release 6.0 11/03/01
- LG GS50-5FY notebook
Angelika Jurkiewicz: CmosPwd /k can remove supervisor password.
- TI Extensa 600CD
Dathan Alley: CmosPwd /k works

What to do if you can’t use cmospwd to clear your cmos ?
Under Dos/Win9x, you can use debug to reset cmos CRC stored at 0x2E-0x2F
debug
-o 70 2E
-o 71 0
-q
 
What to do if cmospwd don’t work on your PC ?

Try to clear password with cmospwd /k.
If cmospwd /k doesn’t work, password is stored in an EEPROM. Try to find a
reset jumper on your motherboard or contact your PC vendor.
If it works, I can try to discover how passwords are encrypted.
I need to know what Bios you used and
some cmos memory backup with their passwords. (cmospwd /w backupfile)
For passwords, choose
- some 1 and 2-letter passwords
- BBBBBBB
- BBBBBBC
- BBBBBCB
- BBBBCBB
- BBBCBBB
- BBCBBBB
- BCBBBBB
- CBBBBBB

Airties RT210 — 192.168.2.1 logine tıkla
Allied telesyn — 192.168.1.1:8080 manager friend
Apache — 192.168.1.1/setup veya root root
Asus — 192.168.1.1 admin admin
Aztech — 10.0.0.2 admin admin
Aztech — 192.168.1.1 admin admin
Billion Bipac — 192.168.1.254 admin password
Cnet — 10.0.0.2 admin epicrouter

Modem default şifreleri
Corecess 3112 usb — 10.0.0.3 admin corecess3113
Corecess 3113 eth — 10.0.0.2 admin corecess3113
Dibeg 108 — 192.168.1.1 dare (boş geç)
D-Link — 192.168.1.1 admin admin
Datron ETHERNET — 192.168.1.1 admin admin
Datron USB — 192.168.1.2 admin admin
Dost GVC — 192.168.1.254 dost dost
Eicon Diva — 10.0.0.2

Modem default şifreleri
Geek — 10.0.0.2 admin epicrouter
Geek — 10.0.0.2 admin geekadsl (Yeni Modeller İçin)
hicomm — 10.0.0.2 admin epicrouter
Inca — 10.0.0.2 admin epicrouter
Loopcom — 10.0.0.2 admin epicrouter
Link SYS — 192.168.1.1 admin admin
Mercury ADSL — 10.0.0.2

Modem default şifreleri
Origo — 10.0.0.2 admin kont2004
paradigm — 10.0.0.2 admin epicrouter
pikatel — 192.168.7.1 DSL DSL
Speedcom — 10.0.0.2 admin conexant
SpeedTouch 330 — 10.0.0.138 şifreyi password’u kendin belirle
Speedtouch — 10.0.0.138 şifreyi password’u kendin belirle
Tecom — 192.168.1.1 root root
Thomson — 10.0.0.138 şifreyi password’u kendiniz belirleyin.
USB Robotics — 10.0.0.2 admin admin

Modem default şifreleri
Zoom X Serisi modem — 10.0.0.2 admin zoomadsl
ZyXEL — 192.168.1.1 admin 1234
siemens speedstream 192.168.254.254 admin admin

Vista için ise
1. Masaüstünde boş bir yerde sağ tuşa tıklayın.
2. Kişileştirmeye girin.
3. Sol Kısımdaki Masaüstü simgelerini değiştir basıp
4. Geri dönüşüm kutusuna tıklayın. Böylece sorununuz çözlümüş olacaktır.